All humanoid robots
Open-source humanoidBuild from open-source files

InMoov

I
InMoov

France · Reviewed 2026-08-15

Gaël Langevin's life-size, open-source 3D-printed humanoid project for makers, educators and researchers.

Published offer

Open-source build; no single retail price

Availability: Build from open-source files

01 / At a glance

Understanding InMoov

Release
2012

Intended applications

DIY robotics, education, accessibility experiments and human-robot interaction

MakersEducationResearch

02 / Hardware profile

InMoov specifications

Category
Open-source humanoid
Commercial status
Active open-source project
Availability
Build from open-source files
Released
2012
Country of origin
France
Target markets
Makers, Education, Research
Use cases
DIY robotics, education, accessibility experiments and human-robot interaction

03 / Pricing and purchasing

Published offers and availability

No numerical offer recorded

Contact InMoov for a written quotation for the exact configuration, including delivery, support and any software access fees.

04 / Technical analysis

InMoov engineering analysis

How difficult is it to reproduce an InMoov arm with consumer 3D printers?

InMoov is Gaël Langevin's open-source, full-scale printed humanoid project. Printed joint tolerances, filament choice, servo models and tendon tension can vary between builders. A digital hand file is therefore insufficient to guarantee the same fingertip forces or movement range in two independent builds. Its educational strength lies in accessible mechanical assembly and visible control mechanisms; a home-built unit should not be described as a certified assistive or medical device.

Configuration and hardware details

01

What exactly is open source on the InMoov build?

InMoov was created by Gaël Langevin as an open-source, life-size 3D-printed humanoid project. It is not one fixed factory-assembled product with a single universal bill of materials, degree-of-freedom count or warranty. Individual builders can choose printers, electronics, servos, control software and assembly methods that alter the result. Describing the design as open source does not mean every completed InMoov shares an identical motor controller.

A maker evaluating InMoov should start from the original documentation and repository for the intended hand, arm or full-body build. Document material, print orientation, servo part numbers, wiring, battery safety and calibration before comparing motion across builds. Open files support experimentation but do not establish medical suitability, certified human-safe contact or effortless assembly.

Hands-on technical guide

InMoov: ordering, setup and first controlled test

Commissioning checklist; examples have not been tested on physical hardware by TechniaHQService.

What to order and verify
This is a self-build project. Download the official printable files for one revision and order the compatible servos, controller, power supply and wiring listed in its bill of materials.
Software and equipment
InMoov printable model files and electronics documentation, slicer, compatible servo controller and MyRobotLab where supported by the selected build.

InMoov workflow

  1. 01Order / accessInMoov
  2. 02SoftwareVersion-matched tools
  3. 03Initial checkRead-only diagnostics
  4. 04Acceptance testSupervised exercise
Conceptual workflow for the exercise below. This is an explanatory diagram, not an electrical wiring schematic or proprietary controller blueprint.

Step-by-step setup and first exercise

  1. 01

    Get the unit and files

    Use the exact bill of materials and assembly instructions; check servo voltage, stall current and controller rating before wiring.

  2. 02

    Install the approved software

    InMoov printable model files and electronics documentation, slicer, compatible servo controller and MyRobotLab where supported by the selected build. Install on the supported host OS and verify the release/build number. Do not use packages intended for another robot.

  3. 03

    Startup and stop check

    Start with a current-limited supply and one disconnected or unloaded actuator; calibrate neutral and movement limits before connecting other joints.

  4. 04

    First exercise

    Print and assemble one finger or hand first, move a single servo through calibrated travel with current limiting and verify the tendon routing before assembling the torso.

  5. 05

    Firmware and software updates

    Compare the current serial/model, controller and firmware versions against the manufacturer's release notes. Export configuration and logs and check recovery options. Obtain the correct signed package or managed update; use the specified power and network conditions. Test stop controls and the same acceptance exercise after updating. If no authorized firmware path exists, do not flash the robot.

  6. 06

    Walking, running and dancing

    Only request a supported standing, walking or performance preset from the manufacturer. For a custom dance or run, obtain the exact joint model and validated controller, retarget motion in simulation, constrain joint position, speed, torque and contacts, then use vendor-supervised reduced-speed commissioning. No running or dance capability is implied by this procedure.

Troubleshooting

Controller cannot establish a connection
Verify the host OS, firmware compatibility, authorized account and network setup using the exact delivered manual; do not bypass safety or authentication.
Motion differs from the acceptance exercise
Stop using the approved control, record the exact fault and verify actuator/joint configuration and software revision before repeating.

Capabilities and limits

The acceptance exercise is a proposed commissioning check, not a measured performance result or proof of support for custom locomotion.

Community ratings

InMoov Reviews & Ratings

Hands-on community feedback is moderated before publication. Technical sub-ratings are optional.

—

0.0(0 reviews)
5 star
0%
4 star
0%
3 star
0%
2 star
0%
1 star
0%

Published reviews

0 total

No published reviews yet

Be the first to submit hands-on feedback for moderation.

06 / References

InMoov sources

Published specifications and supplier information are distinguished from independently measured performance.

  • Official InMoov project (manufacturer)
  • Official InMoov GitHub organization (verification)